![how to shutdown cisco virtual wireless lan controller how to shutdown cisco virtual wireless lan controller](https://www.cisco.com/c/dam/en/us/td/i/400001-500000/400001-410000/409001-410000/409341.tif/_jcr_content/renditions/409341.jpg)
- #HOW TO SHUTDOWN CISCO VIRTUAL WIRELESS LAN CONTROLLER CODE#
- #HOW TO SHUTDOWN CISCO VIRTUAL WIRELESS LAN CONTROLLER PASSWORD#
The only standard left to enable is the standard 802.11n. Configure the settings according to the figure below. Next, switch to enable the standard 802.11a for 5 GHz by selecting 802.11a/n | Network. If 802.11b needs to be supported, it may pay off to disable the lowest rates, in order to avoid clients being attach to an AP far away, unwilling to roam. If you want to support also the 802.11-b standard, set _Mandatory_ for the lowest 802.11b-rate that you want to support (1 Mbps, 2 Mbps, 5.5 Mbps or 11 Mbps), set _Supported_ for all data rates higher than this rate and _Disabled_ for all rates lower than this rate. Enable 802.11g according to the figure shown below. Enabling the 802.11b-standard will result in less available capacity on your network and therefore it is recommended to enable only the standards 802.11g and 802.11n. First, choose WIRELESS and then 802.11b/g/n | Network. The next step is to define the wireless network, which has to be done separately for 2,4 GHz and 5 GHz. Once the access point has found the controller, it stores the IP of the controller, and it can connect to it from any network, as long as the network allowed access in the ACL (see previous section). If this is not the case, the IP address of the controller must be find from the name server by the name CISCO-LWAPP-CONTROLLER. If the access points are connected to the same subnet as the controller, they will automatically find the controller and connect to it. Inbound means packets towards the controller and outbound means packets towards the WLAN clients.Īfter you have specified the ACL you need to take it into use by first selecting Access Control Lists from the side bar and by choosing your ACL and specifying the CPU ACL Mode to Wired or Both. the address(es) of the RADIUS server(s)Īn example of an ACL is shown below.
![how to shutdown cisco virtual wireless lan controller how to shutdown cisco virtual wireless lan controller](https://www.cisco.com/c/dam/en/us/td/i/400001-500000/400001-410000/409001-410000/409349.tif/_jcr_content/renditions/409349.jpg)
![how to shutdown cisco virtual wireless lan controller how to shutdown cisco virtual wireless lan controller](https://www.cisco.com/c/dam/en/us/td/i/400001-500000/400001-410000/409001-410000/409331.tif/_jcr_content/renditions/409331.jpg)
Warning! No AP will come up unless the time is set.Ĭonfiguration correct? If yes, system will save it and reset.
#HOW TO SHUTDOWN CISCO VIRTUAL WIRELESS LAN CONTROLLER CODE#
Please see documentation for more details.Įnter Country Code list (enter 'help' for a list of countries) : Ĭonfigure a NTP server now? : no #Will be done laterĬonfigure the system time now? : no #Will be done later Warning! The default WLAN security policy requires a RADIUS server. Virtual Gateway IP Address: Įnable Symmetric Mobility Tunneling : NOĬonfigure a RADIUS Server now? : no #Will be done later 3ĪP-Manager is on Management subnet, using same valuesĪP Manager Interface DHCP Server (.2): Management Interface DHCP Server IP Address: esim. Management Interface VLAN Identifier (0 = untagged): Service Interface IP Address Configuration : DHCPĮnable Link Aggregation (LAG) : NO
#HOW TO SHUTDOWN CISCO VIRTUAL WIRELESS LAN CONTROLLER PASSWORD#
Welcome to the Cisco Wizard Configuration ToolĮnter Administrative User Name (24 characters max): Įnter Administrative Password (24 characters max):